Search results

I have an Exmark Zero-Turn with a 29 HP EFI Kohler engine. The engine has 1645 hours on it and when the PTO is engaged it bogs down when it runs into heavy grass. The Kohler Engine manual shows an diagnostic computer to troubleshoot the governor but I haven't been able to locate it on the mower...

I have a question, we have a LX277 in our shop with a Kawasaki engine. It was dropped off with the complaint it would only run at 1/2 throttle amd it would break the deck springs. We pulled the engine and inspected the governor and it appeared ok. But, when we reassembled the engine and...

We have a Kohler CV 740-0200 in the shop. We are doing the ignition coil update to get rid of the factory bad design. We updated the harness, installed the new coils, and now as we are trying to start it it will only act like it will try to start. We installed a new switch (old one was bad) and...

We have a Kohler Engine on a Bush Hog Zero turn mower giving us some real issues. It demonstrated losing fire on one coil when it got hot then losing fire all together. Tracing that tissues we discovered a defective Ignition Box (as well as a Kohler Fix calling to remove it all together with a...

I have a John Deere GT 235 in the shop and the customer is stating the brakes will not hold. The local dealer is uncooperative when I called requesting to purchase a service manual for this particular machine (customer frequently brings machines in for service.) Can anyone help? I would greatly...

We have an older Craftsman Riding Mower in our shop that came in with a CV 16.5 Kohler engine that had blown up. I couldn't find one of those but I did find a CV 13 that checked out good so I bought it. After a BIG headache with multiple wiring issues we got the mower running. Now, we thought we...

Got a question, we have a GT 5000 in our shop that came into our shop after being disassembled by the brother of the owner. We have resolved many issues with it but we discovered the rod that disengages the hydostatic drive is disconnected. The diagrams I pull up do not show where it hooks up...

Does anyone have a deck belt diagram for a 54in Gt235? The man I work with took one apart and cannot remember how the belts were routed. I would greatly appreciate any help! Thanks as always!!!!!: :thumbsup:

I have a coworker with an older 1420 with a PTO issue. The original PTO flew apart, so we replaced it, as well as the switch and the relay. But when we went to get it running, the PTO will not engage. It will "click" but not engage. The mower had previously set for at least 2-3 years and it had...

A customer brought a Cub Cadet Enforcer into our shop with a major electrical issue. The original Kohler engine had blown up, so he installed a larger Kohler 24HP Model (KT-735-3104) replacement engine which was not interchangeable with the factory harness. Well, he cut and spliced the original...

I need some help. I changed the bottom end gasket on a Briggs and Stratton 23HP Intek engine. I marked the governor shaft where it was set before I removed the sump. In my zeal to clean up the sump before I reinstalled it, I wiped off my reference mark. I have put the engine back on the mower...

I have a Stihl HT 75 hat has came to me with a no start issue. The guy who owns it took it apart to clean it and when he put it back together it wouldn't start. He brought it to me and I found the following things: 1. It passed the vacuum test with flying colors, absolutely no leakdown. 2. The...

I have rebuilt 2 Stihl Cutoff saws that were extremely abused (ran with no air filters, ran with too lean of air/fuel mixture for example..). I replaced the piston, jug, carbs, coils (firing intermittent) and the saws stubbornly refuse to start. Both are firing, have fuel going to the primer...

A 17.5 Briggs and Stratton came into the shop I am employed at. The previous mechanic has done an extensive amount of work on the engine (over $600.00 for parts and labor) and yet it still has issues. It seems after the last mechanic put it back together, it started pumping oil up the line...

I am working on a MTD engine model 5x65ru. It came into my shop with a carb full of rust and would not run. I flushed it out and put it back together and it now runs. But, it is running at a much higher rpm than it should. I have searched for diagrams of the linkage and cannot find them. Where...