Search results

11A-A2SD791 CMXGMAM2703840 Mower starts fine when cold but after I shut it off, it will not start again until extremely cold. Coil is good, carb is new, compression is good. I tested the choke with my torch, the spring does move the linkeage enough to close the choke plate. I think I have...

I have a Craftsman M105 mower that won't start. Model # 11A-A2SD791 CMXGMAM2703840 I tested the compression - and that is good. I took off the valve cover to make sure both valves are opening and closing - they are I squirt the carb and spark plug hole with starting fluid - and used my drill...

I have a Craftsman M140 mower with a Honda GCV 160cc engine. The mower is difficult to start - usually takes 4 pulls. I have cleaned out the carburetor, gaped the plug to .30 and the gap between the flywheel and the coil looks right,- but the first start of the day is always difficult. I have...

B&S Model No. 128M02-0952-F1 Mower starts easily, but when restarting after sitting for a minute or so, it backfires through the exhaust. It doesn't do it if the mower sits for 10 minutes or so. The engine runs fine otherwise and always starts easily. The backfire happens even before the...

The sticker on my Lawn Mower fell off and I would like to know what the model # is. The numbers that are stamped onto the plate above the muffler are: 8 MO2 0014-F1 14032257 DOM Mar 2014 Any help with a model #? Thanks

Lawnmower won't start. New Carburetor, spark plug, oil and air filter. I suspect the auto choke has failed, but can't find the part # on any parts diagram I found on line. Can anyone supply the parts diagram or part #? Is the auto choke serviceable? Any thoughts? Thanks

Mower is hard to start: I rebuilt the carb, new air filter, new spark plug, the coil checks out fine with a spark tester and with my multi meter. I have cleaned out the gas tank and the fuel line. After it does start and runs for a while, it re starts without issue. The primer bulb looks...

Husqvarna Model 060311M 023782 After carburetor replacement, the engine would surge. I removed the idle jet from the carb and drilled it out with a very fine drill bit. This corrected the idle surge. New problem is that when I push the mower back and forth quickly, or when I come to a stop...

Craftsman 6.75 motor. The pull cord is extremely hard to pull (the break is not touching the flywheel) and compression is at 40lbs. Cannot start mower. I'm guessing there is internal damage = throw it away? Thoughts? Thanks,

I picked up a Troy Bilt Model # 11A-A26M066. The recoil cord would not rewind. I took the housing off and found that the retainer that kept the Ratchet Pawls in place was broken. I replaced the retainer, but now, at times, only one Pawl spins out to engage the flywheel. The other pawl, doesn't...

I need a grass catcher for a Yardman 12A-18M7002, I don't want to pay $75.00 for the bag and the frame. Does anyone know of any other manufacturers grass catchers that will fit this machine or where to get a used one, inexpensively? Thanks

I have a 12A-18M7002 MTD Yard Man Self Propelled 173cc OHV mower. This model has the Kohler engine. It is difficult to start but will eventually start and run terribly. It spits and sputters. I have: Changed the spark plug Drained the gas, cleaned out the tank and used new gas Took the...

When tilting the mower while running and cutting the grass, the blade is hitting the underside of the deck. The deck is not rusted at all and the blade is installed correctly and I don't think the blade is bent. Should I just bend the blade equally to create more space between the blade and...