Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 26
  1. #11

    Join Date
    May 2010
    Posts
    5,438
    Location
    Kansas, Butler county, Just east of DooDah
    Mower
    CTL

    Re: Pull cord won't retract

    If you loosen the screws that hold the rope rewind mechanism to the engine... does the rope rewind?

  2.  

  3. #12

    Join Date
    Feb 2011
    Posts
    25
    Location
    Texas
    Mower
    Craftsman

    Re: Pull cord won't retract

    No, it still required a screwdriver assist.

    I want to go with clean / dry, but I am now looking to this forum for tips on how to re-wind the spring. It came unwound, and I'm having difficulty getting it rewound inside its shallow cup, because my hands don't work so good anymore.

    Thanks,
    Gary

  4. #13

    Join Date
    May 2010
    Posts
    5,438
    Location
    Kansas, Butler county, Just east of DooDah
    Mower
    CTL

    Re: Pull cord won't retract

    Gary...
    Can you post a picture of this mechanism?
    What engine make is it or what model ?? KennyV

  5. #14

    Join Date
    Feb 2011
    Posts
    25
    Location
    Texas
    Mower
    Craftsman

    Re: Pull cord won't retract

    Will do as soon as I can get my camera from work and take a pic.

    I'll look at the model, etc., then as well.

    Will post back

    Thanks,
    Gary

  6. #15

    Join Date
    Feb 2011
    Posts
    25
    Location
    Texas
    Mower
    Craftsman

    Re: Pull cord won't retract

    Forgot my camera...
    I finally got the spring re-wound, by starting with the outer coil and working my way in.
    Its all dry now, and I got the rope rewound as well.
    Pulls good, multiple times, without spark plug.
    But when spark plug is installed, it pulls 2-3 times, and hangs in the out position.

    I don't see a flywheel keyway, so I don't suspect that.
    It fires, but hasnt run for more than a couple of seconds.
    Seems to have a kickback

    I cleaned the carb, and the exhaust screen is clean

    What else could I be missing?
    From what I can see of the cylinder walls, they look clean.

    I found a little melted plastic under the clutch, and cleaned that up

    Its a Craftsman, Hedge Trimmer MN 358.769358, 25cc, mfg. in 2006, with 50 hours expected life hours.

    Thanks,
    Gary

  7. #16

    Join Date
    Jul 2010
    Posts
    90
    Location
    Canada
    Mower
    I Don't Own a Mower :(

    Re: Pull cord won't retract

    We have a similar issue with the lawnmower we bought second hand. It worked well, but after so many pills it is extended and won't retract at all.

  8. #17

    Join Date
    Feb 2011
    Posts
    25
    Location
    Texas
    Mower
    Craftsman

    Re: Pull cord won't retract

    I found my model on the Craftsman parts website, and apparently it does have a flywheel key.

    I will investigate further to see if the key is broken. That would explain the kickback, and perhaps that is the recoil issue as well.

    Its a small flywheel, maybe 5" diameter...
    Do I use a gearpuller, or is it screwed on?

    I can't tell by looking.. I know... pictures, pictures, pictures..........
    I'll post back when I can remember to bring my camera home from work.

    Thanks,
    Gary

  9. #18

    Join Date
    Feb 2011
    Posts
    25
    Location
    Texas
    Mower
    Craftsman

    Re: Pull cord won't retract

    How do I move this post to the Small Engine repair forum?

    Thanks,
    Gary

  10. #19

    Join Date
    Feb 2011
    Posts
    25
    Location
    Texas
    Mower
    Craftsman

    Re: Pull cord won't retract

    Model No. is 358.769356.
    Now that the kickback seems to be the problem, any ideas on how I can get this flywheel off to check the key?

    Thanks,
    Gary
    Attached Images Attached Images
    Last edited by Papaw50; 03-02-2011 at 10:53 PM.

  11. #20

    1,000 Post Club
    twall's Avatar
    Join Date
    Feb 2011
    Posts
    1,628
    Location
    New York
    Mower
    Snapper SR1433

    Re: Pull cord won't retract

    You shouldn't have to take the flywheel off. The spring loaded tabs on top are what engage with the spinner, and they look OK in your pic.

    Sounds like the problem is the spring isn't tensioned enough. I've run into this a hundred times. You have to 'wind up' the plastic piece, with no rope installed (but the spring and everything else is). Then, when it's pretty (but not completely) tight, Hold it By wedging a screwdriver in the space between the white plastic and the metal retainer (that's not the proper way, but it'll get the job done) just enough to hold it once you've aligned the hole in the plastic spinner with the rope outlet.

    Carefully feed the rope into the holes, and tie a knot (or screw in the wedge/lock in a bit, tough to see in the pic). Fish it around to its original position( screw in wedge/lock here), and then remove the screwdriver whilst holding the pull cord, and let it retract. If you have too much rope, you'll run out of spring tension before you run out of rope. Pull it out again till you have decent (but not too much) tension on the starter rope. Re-tie the knot on the handle end. Don't cut the handle end rope untill you know it retracts, and you have enough rope to pull out without hitting the stop.

    It is a royal pain, believe me, but doable.

Similar Threads

  1. ROPE PULL EASE
    By wfm215 in forum Snapper Forum
    Replies: 18
    Last Post: 04-17-2012, 02:13 PM
  2. Shorter pull string on a craftsman
    By beesnroses32 in forum Build-it Yourself
    Replies: 7
    Last Post: 03-01-2011, 09:14 AM
  3. Pull & twist oil engine drain plug
    By noma in forum Small Engine & Mower Repair
    Replies: 2
    Last Post: 11-06-2010, 09:59 PM
  4. Are electric start mowers more expensive than pull start mowers?
    By beesnroses32 in forum Mower & Equipment Buying & Pricing
    Replies: 5
    Last Post: 07-13-2010, 08:40 PM
  5. Ignition Pull Broke
    By BlueGrass in forum Small Engine & Mower Repair
    Replies: 11
    Last Post: 06-18-2010, 04:05 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •